Search results

I have a fountain and it leaks beneath the coping that is over it. I am not sure what the cause is and I would like to replace the piece. Please tell me how to identify it and how it is likely connected.

Adding back salt after the no drain exchange. Putting salt near main drain and chlorinator is off. Put check system high salt amp warning came on. What steps next?

Just finished a bunch of projects on my pool 1) added Jandy valve between pump and filter 2) moved the flow switch 3) ascorbic acid treated pool 4) added an iphone app by Mark that controls the control board. 5) investigating cause of my dim pentair intellibright lights. I was happy with all I...

I have Intermatic PX300 light transformer box and a Intermatic PX300 light transformer box with my pool equiptment. The 2 lights in my pool are very dim and the one in my spa does not light. I am looking to upgrade things. I plan on keeping my Aqualogic control board. Looking for ideas...

I am continuing to cut the cord from pool service team. I am very involved in balancing. Looking into robotics for my pool. It has a spa separated from pool by a thin wall (? 8 inch wide). Will it clean spa too without being placed in it directly? While I am doing research would like...

Can salt increase spontaneously without addition of salt (to my best knowledge)? Weather about 8 degrees warmer this week. Pool level same. No water added or removed. Is it safe in short run?

Good evening Flow switch issues Bought this switch Sept 2022: Amazon.com Bought this switch August of 2023 : Amazon.com Both died: I am wondering if I am installing wrong. I know they are marked with arrows showing the flow and I made sure the sensor was placed accordingly. Not 100 % sure...

Pool between 7-10 years. Not sure. Possibly acid washed 1-2 x in past. (not sure). Pool guy says I can acid wash again because of both dark and light stains. How do I know if I reached my limit on acid washing and need to go with the resurfacing? Is there something I can inspect further?

I have an older Hayward controller: goldline aqua logic circuit board "g1-066008k-1" Smelled smoky and there was a communication error. Many years ago I repaired the solder joint on the corner relay. This time I flipped the board over and re-soldered the joint. I did the job very fast in the...

Gentleman: I have a resurfacing question, I have a 12-15 year old swimming pool in south Florida. It is approx 25 x 50 feet and currently has a diamond brite type of surface. Over the years it has discolored and my wife wants to have it re-surfaced. She has had a few vendors over. Some...

I have an inground pool in South Florida perhaps 1/8 mile from ocean. It has a small spa. Over the last 30 years I think I have had 4 gas heaters. Most of them rust away because of the hot salty climate. Down here we only use heaters Nov to March and maybe even less. Personally I would...

I live in Florida and removed my water heater for the time being. I want to put in a water sensor so the check light goes off on my prologic. I should simply put in the pipe that leads from the pump and leads to the prevously removed heater. Right?

Hello! A few minutes ago I removed my Hayward Goldline Turbocell T15 and replaced it with one I bought online (new in box) This is my system: https://hayward-pool-assets.com/assets/documents/pools/pdf/troubleshooting-guides/prologic-aqualogic-consumer-trouble-shooting-guide.pdf The check light...

I mentioned in another post that my previous pool repair person put in a new filter but somehow removed the water temperature sensor and air sensor just lying on the ground. How do I actually put in new sensors if there is no old one to remove?

Hi my name is bill and I am a newbee I have a Hayward Aqua Pro Logic system The other day my pool person told me there was "no flow" and the cell was dead. So I replaced the flow switch successfully and now there is flow The cell seems dead as it says low salt 0000ppm and also the pool temp...