Search results

look into hot sun industries for solar they are great on dyi, and they will help you design a system. www.h2otsun.com

if you're going to do solar have a solar return on the bottom of pool. that will warm up the pool from the bottom. i was taught that from my pool plumber and it works great.

I have built 3 pools and acted as the gc on them and when I bought this house it already had a pool so I was stuck with all of the poor workmanship. spa isn't deep enough, only reaches midway to my chest and has no air blower for jets. brought in my pool plumber to see about the jet problem ...

okay that clears something's up, but top left relay is not plugged into board. I will recheck board tonight

top left relay is not being used, power for pump comes from breaker to pump. I know it should go - breaker-relay-pump but pb didn't wire it that way. what's crazy is that it a 5 yr old pool built by a VERY VERY large southern calif. pb I will take photos tonight and post them.. I may just...

thanks

i was looking for the pump relay to take off of but nothing in the cb

i checked and no relay comes on when pump is running i have three relays #1 pool/spa lights, #2 yard lights, #3 pump for slide

I'm familiar with pentair relay wiring but this is different. power comes right from the breaker to pump, pump has power at all times put not switched on. i just checked and it has power at all times. pump model #vsshp270aut do i rewire like a pentair-using a relay or can a jandy expert...

trying to wire up a new aquapure and I'm not sure where blk/load 1 and blk/yel /load 2 go. builder ran power from breaker in aqualink to epump, with control of pump thru rs485 cable. if I go to L1 & L2 on pump for power for aquapure then aquapure is powered up always. do i rewire pump to a...

Yes, i moved to a new house. i need to update my profile

I have a Aqualink system for automation and i want to put in a swg. What swg's will work with the aqualink control system - to control the swg thru the aqualink thanks jim

the spa runs no problem with the cable hooked up to the pump, spa side and indoor panel will turn on pump for spa. when I push the pool button on the spa side or the indoor panel, pump will not run when cable is plugged into the pump. i'am going to look into having board looked at thanks jim

my indoor panel shows all that data, but no pump action. pump display shows "display not active" when spa is on start/stop on pump is lite. spa side is new, old one had taken out board before. board was repaired, never got the pump to run-only when spa button in house panel was pressed on. I...

i have set speeds and times for the pool to run, salt cell is powered up and looking for water flow when pump is supposed to be running but pump is not running. it seems to not be getting the signal from board? spa will run form indoor panel or spa side switch but no pool function thanks jim

i have a intellitouch system with a pentair vs pump running both pool and spa. i can't get the pool to turn on-spa no problem. if its in service mode or using the indoor panel - i can hear relay switch but no action at pump. i have set a start and end time for pool running , what is wrong...

it could be the giant donut sprinkles plugging the holes lol

pool builder didn't install a drain?

i believe it all started with the spa side switch getting water in to it, so thats why i was thinking the spa switch took out the boards. i have opened up the mobiletouch to find a new battery for it, and the goo is nasty. i will take indoor panel and boards to my sisters house this wkend to...

not sure of your reply?

so i took all 4 boards and checked them as you can see when i go to advanced menu i can't retrieve outdoor control info maybe indoor control problem?

thanks guys, will check tonight jim

i swapped sensors and installed new sensors

look up pour a lid, its a lid for the skimmer

I have a 14 yr old system that is driving me crazy. it started out with a bad spa side switch that i took off the system. I cant set the time and i have no water temp reading and air shows 0 degrees. I swapped temp sensors-no change. i have a indoor panel, old mobiletouch handheld, and a new...