Search results

I just purchased Beta SE from Amazon (prime days) $375.00 and 2 years protection from Asurion inc. Just wonder is anyone experience with this extended warranty ? compare to Betabot extended warranty? Can I buy extended warranty from Betabot? thanks

Hi, My Polaris booster pump is suddenly did not start, it was controlled by Intermatic P1353ME. Installed in 220V mode, 1 hot leg direct to pump, and 1 hot leg is triggered by timer. I checked every is OK on timer, but on the pump I found weird problem, which without trigger from timer, 2 hot...

Hi, I just bought a 24vac transformer to automate (by Sonoff 4ch pro r3) my Compool cva-24 actuator (24vac), and 24vac contactors. The output of transformer is around 28vac (no load), is it will cause any problem? Thanks

I still had a bunches of 3" Sanitized tabs, is it OK to use for my pool for raising CYA ? 3" tab ==> CYA? thanks

Here is my pool was on 05/15 FC = 6.5 CC = 0 PH = 7.3 TA = 70 ( aeration from 150) CH = 300 CYA = 85 Salt = 3800 temp = 68 F Last 3 days, FC droped to 4.0 (SWG 100% 5 hours/day). so I wanted to raise FC = 6.0 or above, SWG ran 100% 10 hours /day). Noticed for last couple days my FC still at...

FC = 6.0 PH = 8.2 TA = 120 CH = 300 CYA = 85 Salt = 3800 On process to lower TA by Aeration, accidentally put 1 gal of 14.5% Muriactic acid. Should I raise PH by Borax or keep aerate ? Thx in advance.

Just let me share the lately info on RJ45 (with software version R6.10). I noticed during RJ45 cycles running (I set it at 50%), it stopped (after 2 or 3 hours, I'm not sure) and then it start running (after it stopped for 1 or 2 hours, I'm not sure). ? I called and talk to tech support and they...

My pool was past the break in period (over month) after resurface plaster. Yesterday added salt, ran pump for 24 hours, test and these are the results: TC =3 FC = 1.5 cc = 0 PH = 8.0 TA = 110 CH = 325 TYA = 75 Salt = 3500 ppm. Do I need to wait until water balance, or I can start running SWG ...

Hi, I just replaced old 1.5 HP single speed pump with new Pentair Intelliflo 011018. I noticed when pump runs max speed (3450 RPM while priming on start up)), my DE filter ( just clean) pressure go over 30 PSI ? is it the new pump over power ? Pls help. thx

Need your advise to install new Pentair 011018. If I install normally like my old pump (image attached) which suction line in front, control panel inside then it will be hard to program on the control panel which is upside down (no available space to stand inside). Can the control panel turn...

Because of install Circupool RJ45 (18,000 gallons pool), I'm thinking replace my single 1.5 HP single speed pump with VS pump. Is it worth? my local electric rate is 0.2 - 0.9 cents (depend on day time). Which VS pump should I buy ?( I'm interesting on Pentair 342000 ) What RPM should I run to...

My 18,000 gallons pool is re-plastered, and 1st go with SWG Circupool RJ45 (on sale). RJ45 chemistry water level: FC 1.0 - 3.0 ppm Salinity 3000 - 4000 ppm pH 7.2 - 7.8 Total Alkalinity 100 - 200 ppm Calcium Hardness 200 - 400 ppm...