intellitouch

Hi Everyone, I have an Intellitouch system that has a dedicated pump for my jets in my spa. When I tell the system to call for the pump to turn on, it appears that the circuit is being activated but the pump doesn't actually ramp up. Can anyone point me at what might be the culprit? Thanks in...

I’ve been struggling with an issue for the last month and hoping someone knows what is going on. I have a Pentair Intellitouch system that is changing the speeds of the Pentair variable speed pump when on the aux 3 port which is basically just a speed change for the floor cleaner. What happens...

The three lights on the left (auto, service and time out) are lit red. If I unplug the left com port. The light will go back to the point where I can choose between (auto, service and time out) but the system wont run even on service. Sometimes all the lights on the system are red and sometimes...

Hi folks, I am trying to troubleshoot my filter pump that previously worked fine for many years. The pump no longer runs upon command from the controller. The pump is an IntelliFlo 4 160. The controller is an IntelliTouch i9+3. The pump runs fine in manual mode, confirming power is at the...

I have added the automated bypass to my master temp and intellitouch controlled Pentair system. While everything works well when heat is called for: ie the bypass valve activates and starts allowing water to flow to the heater before the heater starts, when the temp is reached or the...

Hello All, Long time lurker, infrequent poster here. I was poking around in my Pentair system and noted that we are running FW 1.170 where as the latest firmware is 1.190. I have already found and read through the thread telling me how to update the FW (including the programmers needed, the...

Where does the comm cable go for the mastertemp from the intellitouch? I want full functionality on from inside and at the automation and all I’m finding is using the fireman’s switch to turn on/off the heater at an existing setting. I want to be able to adjust the temp from inside. Where on...

I need to fix the board of my Intellitouch and as a result thinking of replacing my Intellitouch with the Intellicenter (using Pentair 522047 upgrade kit). I am quite handy and do most of these activities myself. I am planning to install the kit myself and have a couple of quick questions: -...

Hi all, Looking for advice on replacing my failing rebuilt Whisperflo II 2-speed 1-hp 240V pump controlled by a 2004 Intellitouch/easy touch P4 system (motherboard upgraded to UOC: 2.160, Bootloader UOC: 1.010). In addition to the pump, the system controls a Jandy Valve for the solar panels, the...

I'm a new pool owner and my pool builder has been a bit lacking on the education front. I feel like a bonehead, but I cannot figure out how to get schedules that use different pump speeds. I'm not sure where I will land speed/schedule wise, but those particulars aside I cannot figure out what...

Hello everyone! We are currently building a pool here in Utah. Here’s a little background: The pool contractor we went with has recently started shifting from landscaping to building pools. We are not worried about his expirence level as he has 20+ years of expirence of building pools. (Before...

I was hoping to get some clarity around smart/app based system. My PB is using Pentair products and is offering EasyTouch for upgraded Smart functionality. I have been reading online and most of the information I find is Intellitouch from Pentair. Is there a difference between EasyTouch and...

I just replaced a intellitouch I5+3 personality board and motherboard with an I9+3 so I could add additional aux circuits. After startup with the new I9+3 board the display only recognizes the original 5 Aux circuits. It wont show the additional open Aux circuits. menu-set up- advanced-circuit...

I recently had my main controller board fixed and I just reinstalled it. I can control the cleaner and I can hear the "clicks" when I activate the main filter pump. However, the pump is not recognizing the Intellitouch and is in manual mode (working just fine otherwise). I wonder if it could be...